Scope RS232 Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Dálková ovládání Scope RS232. Communication Protocol dVision 35 and dVision Scope displays Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 14
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Communication Protocol
dVision 35 and dVision Scope displays
Zobrazit stránku 0
1 2 3 4 5 6 ... 13 14

Shrnutí obsahu

Strany 1 - Communication Protocol

Communication ProtocoldVision 35 and dVision Scope displays

Strany 2 - Connecting to the projector

13Command DescriptionOperations supportedCommentsLens controlFOIN Focus InSet 1-Slow,2-Medium,3-FastFOUT Focus Out Set 1-Slow,2-Medium,3

Strany 3

14Command DescriptionOperations supportedCommentsSNS1 Sensor Value 1 GetSNS2 Sensor Value 2 GetSNS3 Sensor Value 3 GetSNS4 Sensor Value 4 GetSNS5 Sens

Strany 4 - Acknowledge/Response

15Value tablesIABS Set source abs values Value Description0 VGA 11 VGA 22 DVI 17 Component8 HDMI110 DVI 211 HDMI212 Dual Head DVI13 DualHeadHDM

Strany 5

16ORIESelect Orientation abs valueValue Description0 Desktop front1 Ceiling rear2 Desktop rear3 Ceiling frontOSDCOSD Enable Value Description0 OSD o

Strany 6 - ASCII protocol

17ORIESelect Orientation abs valueValue Description0 Desktop front1 Ceiling rear2 Desktop rear3 Ceiling frontOSDCOSD Enable Value Description0 OSD o

Strany 7 - - Advanced

4Setting up LAN communicationThe projector is shipped with a set of default settings, these are as follows:Description ValueDHCP OnIP address 0.0.0.0

Strany 8

5Communication ProtocolThis section describes how to use the communication protocol to control projectors remotely.When the projects are connected to

Strany 9

6Acknowledge/ResponseAcknowledge is optional and ON by default. Auto acknowledge can be turned on and off with ECHO commad. It can also be activated o

Strany 10

7INCREMENTCONTRAST: C N T R R 1 ‘CR’:CNTR R1’CR’ACKNOWLEDGEINCREMENTCONTRAST% 0 0 1 C N T R 0 0 0 0 6 1 ‘CR’%001 CNTR 000061’CR’DECREMENTCONTRAST

Strany 11

9ASCII protocolShowing all properties for available commands.Command DescriptionOperations supportedCommentsPOWR Power Get,

Strany 12 - Value tables

10Command DescriptionOperations supportedCommentsDSGY Desired Green Y Get, SetDSGG Desired Green Gain Get, SetDSBX Desired Blue X Get, SetDSBY Desired

Strany 13

11Command DescriptionOperations supportedCommentsPicture->Advanced->InputCroppingCTYP InputCroppingMode Get, Set 0 - Disabled, 1 - Auto, 2 - 2

Strany 14

12Command DescriptionOperations supportedCommentsInstallation->triggerTRG1 Trigger1Mode Get, Set SeevaluetableTRGxTRG2 Trigger2Mode Get, Set

Komentáře k této Příručce

Žádné komentáře